butt joint
英 [bʌt dʒɔɪnt]
美 [bʌt dʒɔɪnt]
对接
英英释义
noun
- a joint made by fastening ends together without overlapping
双语例句
- Based on the characteristics of such weld pool images, the algorithm of image processing is designed. The whole edge of weld pool is extracted. The parameters of weld pool surface geometry are obtained under different TIG welding conditions of butt joint.
根据对接TIG焊熔池图像特点,设计出图像处理算法,检测出了焊接熔池的整个边缘,得到了不同工艺条件下对接TIG,焊熔池几何形状参数的实际尺寸。 - Test shows that this way can exhibit good result to butt joint and lap joint of TIG welding and accurately abstract welding seam out, to the welding seam of large magnitude dogleg angle shows good tracking effect ( dogleg angle< 68 °) and procession speed< 100 ms.
实验表明,系统对TIG焊的对接和搭接焊缝有很好地处理效果,对大幅度折线焊缝也能很好的跟踪(折线角>68°),处理速度>100ms。 - Creating a butt joint by welding.
通过焊接产生对接接头的焊接。 - Results A total of 24 cases with obstructive jaundice were successfully operated by butt joint of PTBD and ERCP.
结果24例PTBD与ERCP对接胆道支架植入术治疗梗阻性黄疸均获得成功。 - Application of electromechanical integration on TDS 9S top drive is analysed, and study on butt joint in mechanical control logic with control software procedure are introduced in this paper.
分析了机电一体化技术在TDS-9S顶驱上的应用,研究了机械主体的控制逻辑与微机控制软件流程的对接。 - Using the commercial CCD camera, the TIG weld pool surface image of butt joint is captured with high clearance and resolution by optimizing the optical parameters and adjusting the image-grabber parameters dynamically.
利用普通CCD摄像机,通过光学参数的优化和采集参数的动态调整,拍摄出了清晰度和分辨率都较高的对接TIG焊熔池正面图像。 - This paper studied how to attain the distribution regulation of welding residual stress of butt joint of plate after weld toe was TIG remelted and intense cooled by finite element method. It includes residual stress distribution after welded and weld toe TIG remelting.
本文主要研究如何应用有限元法分析平板对接的焊趾TIG重熔层激冷处理对焊趾表面残余应力分布的影响规律,包括焊态和焊趾TIG重熔的残余应力的分布。 - The weld and installation of the plugging triple valve is first step of the plugging procedure. There are two major steps: First, the welded butt joint between the upper and lower backplates.
三通封堵结构的焊接安装是封堵操作的第一步,其主要分为上下护板间的对接和上下护板与管材间的角焊接。 - Owing to the terminals with the steps, the butt joint parts and the connecting parts are not on the same plane.
由于上述端子具有台阶使得对接部与连接部不在同一平面上。 - Most scholars mainly adopted one dimension variation analysis model, and took qualitative analysis on the butt joint, lap joint of the parts in the research field of assembly sequence optimization which targets was dimension quality.
以装配尺寸质量为目标的装配顺序优化研究方面,多数学者主要采用一维的偏差分析模型,对零件间的对接、搭接等接头形式进行定性分析。